BS EN 10080-2005 Steel for the reinforcement of concrete - Weldable reinforcing steel - General
|
ID： |
62E2557E9B8C42698F720745EED037BD |
|
文件大小(MB)： |
0.79 |
|
页数： |
74 |
|
文件格式： |
|
|
日期： |
2010-8-10 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
BRITISH STANDARD BS EN,10080:2005,Steel for the,reinforcement of,concrete — Weldable,reinforcing steel —,General,The European Standard EN 10080:2005 has the status of a,British Standard,ICS 77.140.15; 77.140.60; 77.140.65, , , ,BS EN 10080:2005,This British Standard was,published under the authority,of the Standards Policy and,Strategy Committee,on 23 December 2005,. BSI 23 December 2005,ISBN 0 580 46804 6,National foreword,This British Standard is the official English language version of,EN 10080:2005 but will not become current until 01 January 2006.,EN 10080 is a candidate ‘‘harmonized’’ European Standard and fully takes into,account the requirements of the European Commission mandate M115,[Reinforcing and prestressing steel (for concrete)], given under the EU,Construction Products Directive (89/106/EEC), and is intended to lead to CE,marking. The date of applicability of EN 10080 as a ‘‘harmonized’’ European,Standard, i.e. the date after which this standard may be used for CE marking,purposes, is subject to an announcement in the Official Journal of the,European Communities.,The Commission in consultation with Member States has agreed a transition,period for the co-existence of ‘‘harmonized’’ European Standards and their,corresponding national standard(s). It is intended that this period will,comprise a period, usually nine months, after the date of availability of the,European Standard, during which any required changes to national,regulations are to be made, followed by a further period, usually of 12 months,for the implementation of CE marking. At the end of this co-existence period,conflicting national standard(s) will be withdrawn.,EN 10080 does not include all the requirements to fully specify reinforcing,steels. It is intended that EN 10080 should be used in conjunction with a,Technical Specification, in which the details of the performance characteristics,are specified. Within the UK, three standards have been revised for use with,EN 10080, these are:,— BS 4449:2005, Steel for the reinforcement of concrete — Weldable,reinforcing steel — Bar, coil and decoiled product — Specification,— BS 4482:2005, Steel wire for the reinforcement of concrete products —,Specification,— BS 4483:2005, Steel fabric for the reinforcement of concrete — Specification,EN 10080:2005 is the subject of transitional arrangements agreed under the,Commission mandate. The above standards contain some requirements, which,conflict with EN 10080:2005. Based on the transition period of twenty-one,months, these standards will be further revised by October 2007, so that they,do not conflict with EN 10080.,NOTE This date is approximate. Users of this standard should contact BSI,Customer Services for confirmation of revisions.,Summary of pages,This document comprises a front cover, an inside front cover, page i, a blank,page, the EN title page, pages 2 to 69 and a back cover.,The BSI copyright notice displayed in this document indicates when the,document was last issued.,Amendments issued since publication,Amd. No. Date Comments,BS EN 10080:2005,i,The UK participation in its preparation was entrusted by Technical Committee,ISE/9, Steel for concrete reinforcement, to Subcommittee ISE/9/1, Bars, wire and,fabric for concrete reinforcement, which has the responsibility to:,A list of organizations represented on this committee can be obtained on request,to its secretary.,If CE marking is performed, the procedures in Annex ZA will apply. The,significance of the CE marking is that the product manufacturer claims,compliance with the ‘‘harmonized’’ requirements given in the normative text of,the product standard. These relate to the essential requirements of the EU,Construction Products Directive. Not all product characteristics need necessarily,be given on the CE marking, but those product characteristics covered by,regulations in force in each EU Member State, where the manufacturer intends,that the product will be used, do need to be stated.,Cross-references,The British Standards which implement international or European publications,referred to in this document may be found in the BSI Catalogue under the section,entitled “International Standards Correspondence Index”, or by using the,“Search” facility of the BSI Electronic Catalogue or of British Standards Online.,This publication does not purport to include all the necessary provisions of a,contract. Users are responsible for its correct application.,— aid enquirers to understand the text;,— present to the responsible international/European committee any,enquiries on the interpretation, or p……
……